Fix a Crack in a Cast Iron Wood Stove or Grill

Fix a Crack in a Cast Iron Wood Stove or Grill

Learn more about ExtremeHeat

Seal a crack or leaking seam in a cast iron wood stove, firebox or grill body with J-B Weld ExtremeHeat, a metallic paste rated to 1000°F. With the stove cold, wire-brush the crack, work the paste in and let it set 2 to 4 hours. Let it cure 24 hours and keep water off it, then light a small fire first. Keep it out of direct flame and off any surface that touches food.

Difficulty
Moderate
Working time
45 min
Cure time
Sets in 2-4 hr, full cure 24 hr
Works on
Cast ironSteel

How to fix a crack in a cast iron wood stove or grill

  1. Step 1: Let it cool

    Let the stove or grill cool completely and clean out the ash.

  2. Step 2: Prepare

    Remove dirt, debris or loose contaminants from surface. Use sand paper to roughen. For some repairs, open small cracks further with a drill or screwdriver to create a 1/8" gap.

  3. Step 3: Mix

    Open J-B Weld® Extreme Heat™. Thoroughly mix product.

  4. Step 4: Apply

    Use product generously, working onto surface or into hole, crack, pit or seam. Repeat as needed. Allow 2-4 hours set up, depending on temperature and current environment.

  5. Step 5: Dry

    Test cure by pressing fingernail or thumbnail into repair material. If unable to penetrate, then repair is complete. If area appears slightly soft, use a non-flame heat source, such as a hair dryer, to speed cure time, or allow 24 hours before allowing high heat exposure. Repeat test until fully cured.

  6. Step 6: Break it in gently

    Once fully cured, start with a small fire and check the repair before running it hot.

What you'll need

J-B Weld products

Tools and materials

  • Wire brush
  • Sandpaper
  • Putty knife
  • Gloves
  • Hair dryer (optional)

Frequently asked questions

Can I use ExtremeHeat to repair a cracked cast iron wood stove or firebox?

Yes, on cast iron, for sealing cracks and seams that are not in direct flame contact. It also works for sealing the gap where the stove pipe enters the collar. It is less reliable on sheet steel stove bodies. Because it is water based, keep water off it during and after curing, and do not light the stove until the repair has fully cured.

Is ExtremeHeat safe for grills, smokers, ovens or anything that touches food?

ExtremeHeat is non-toxic once cured, but it has not been tested or rated as food safe, so J-B Weld does not recommend it where it can contact food. That rules out oven floors, cooking pots, baking pans and grill cooking surfaces. Repairs to handles, legs and other parts away from food are different, but grease and cleaning water will still dissolve it.

What is the maximum temperature ExtremeHeat Paste can handle?

ExtremeHeat is rated to 1000 F / 537 C, and J-B Weld support describes that figure as intermittent exposure rather than a constant operating temperature. Older packaging listed 2400 F; after further testing J-B Weld revised the number down to 1000 F, so use the lower figure. Keep the repair out of direct flame contact, which will burn it regardless of the rating.

How long does ExtremeHeat take to set and cure, and can I speed it up?

Allow 2 to 4 hours to set up and 24 hours for full cure before any high-heat exposure. Test it by pressing a fingernail into the repair; if you cannot dent it, it is cured. A non-flame heat source such as a hair dryer will speed the cure. Working time is roughly 15 minutes, and a few drops of water will extend it.

NEED HELP FINDING THE RIGHT PRODUCT FOR YOUR PROJECT

FIND YOUR FIX