The J-B Weld Windshield Saver Kit repairs bullseye, star and stone chips up to 1-1/4 inches in laminated auto glass. Clean the chip, mount the pedestal, inject the resin with the vacuum-and-pressure syringe, then cure it in direct sunlight for 15 minutes. Plan on about an hour. Long cracks need a new windshield.

Difficulty
Moderate
Working time
1 hr
Cure time
UV cure: 15 min in direct sun
Works on
Glass

How to repair a windshield chip

  1. Step 1: Clean the chip

    Remove loose glass from the damaged area and wipe around it with the alcohol towelette. Lay a cloth under the chip to catch any resin.

  2. Step 2: Attach the adhesive disc

    Peel the backing off the green side of the disc and press it firmly over the chip. Check from inside the car that there are no air bubbles.

  3. Step 3: Mount the pedestal

    Peel the other side of the disc. Line the pedestal tab up with the disc tab and press firmly to seal it.

  4. Step 4: Add the resin

    Cut about 1/8 inch off the resin tube tip, set the stem 1/4 inch into the pedestal and squeeze in the resin. Recap the tube to save the rest.

  5. Step 5: Pull a vacuum

    Push the plunger fully in, twist the syringe into the pedestal, pull the plunger up and lock it at the lowest notch. Wait 10 minutes.

  6. Step 6: Apply pressure

    Remove the syringe briefly to let air in, refit it, push the plunger down and lock it at the top notch. Wait at least 20 minutes.

  7. Step 7: Fill and cover

    Remove the syringe, pedestal and disc. Squeeze the remaining resin into the chip and lay the curing strip over it. Smooth out bubbles with the razor.

  8. Step 8: Cure in the sun

    Park in direct sunlight for 15 minutes. Peel off the strip, scrape away excess resin with the razor and clean the glass.

What you'll need

J-B Weld products

Tools and materials

  • Cloth

Frequently asked questions

What damage can this kit fix, and what is outside its range?

It repairs bullseye, star, half moon and stone chips up to 1 1/4 inch in diameter in laminated automotive glass. It is a chip repair, not a crack repair, so a running crack, a chip larger than 1 1/4 inch, or damage that has gone through both layers of the laminate is outside its range. It does not work on plexiglass or single pane glass.

Can I repair a chip in the driver's line of sight?

We do not recommend it. Even a good repair leaves some optical distortion, and damage in the driver's primary viewing area is normally treated as a windshield replacement rather than a repair, including by inspection rules in many states. A crack in that area is a replacement, not a repair. Use the kit on chips outside the driver's direct field of view.

How long does the repair take?

Roughly 45 minutes to an hour. Once the pedestal is fitted you pull vacuum for 10 minutes, switch the plunger to pressure and leave it at least 20 minutes, then squeeze in the remaining resin, cover it with a curing strip and give it 15 minutes in direct sunlight. On a cloudy day allow up to an hour of daylight for the final cure.

How many chips will one kit fix?

One. The resin, the single use pedestal and the adhesive disc are all sized for a single repair, so you need a kit per chip. Work on one chip at a time and start with the most structurally significant one if you are choosing between several. Repair chips promptly, because temperature swings and car washes turn a chip into a crack.

What temperature can I work in?

Keep it above freezing for the application and for the whole cure and you should have no problems. Below freezing the resin thickens and will not flow into the chip. The glass and the chip also need to be completely dry before you start, and the final step needs direct sunlight to cure the resin, so plan the job for a dry day.

NEED HELP FINDING THE RIGHT PRODUCT FOR YOUR PROJECT

FIND YOUR FIX