Hand holding a green fuel nozzle at a car's gas tank

Seal a Leaky Gas Tank

Learn more about TankWeld

Seal a leak, crack or small hole in a metal gas tank with the J-B Weld TankWeld Kit. Drain and vent the tank, sand the area to bare metal and degrease it, then sandwich the included fiberglass cloth between two layers of fuel-resistant epoxy. The kit handles cracks up to 4 inches and holes up to 1/4 inch. The epoxy sets in about 5 minutes; let it cure fully before you refill the tank. Plastic fuel tanks can't be repaired with epoxy.

Difficulty
Moderate
Working time
45 min
Cure time
Sets in 5 min, full cure 4 hr
Works on
SteelMetal

How to seal a leaky gas tank

  1. Step 1: Find and mark the leak

    Locate the leak and mark it with a pencil. Drain the tank and let the outside dry completely before you start.

  2. Step 2: Sand to bare metal

    Sand a few inches around the leak down to bare metal. This removes paint, rust and road grime and gives the epoxy a rough surface to grab.

  3. Step 3: Degrease

    Spray the area with brake cleaner and wipe it down. Repeat until the cloth comes away clean.

  4. Step 4: Cut the fiberglass cloth

    Before you mix anything, cut the fiberglass cloth into a patch that covers the damage with a margin of clean, sanded metal on every side. The epoxy starts to set in about 5 minutes, so have the patch ready.

  5. Step 5: Mix and apply the first layer

    Mix the two epoxy components until the color is uniform with no streaks. Use the applicator to spread about half of it over the damaged area and the sanded margin around it.

  6. Step 6: Embed the cloth and seal it

    Press the fiberglass patch into the wet epoxy so it lies flat with no air pockets. Spread the remaining epoxy over the cloth until it is fully covered and the edges are saturated, then feather the edges onto the tank.

  7. Step 7: Let it cure before refilling

    Keep fuel off the repair and let the epoxy cure fully, at least 4 hours, before you refill the tank or drive. Check the patch for weeping after the first fill.

What you'll need

J-B Weld products

Tools and materials

  • Pencil
  • Brake cleaner
  • Clean cloths
  • Scissors
  • Disposable gloves

Frequently asked questions

What can TankWeld repair, and how large can the damage be?

Cracks of 4 inches or less and holes up to 1/4 inch in diameter, on metal fuel tanks, metal storage tanks, oil pans and similar metal containers. This is a metal kit. It is not recommended for plastic repairs, and specifically not for polyethylene or polypropylene tanks. J-B Weld currently has nothing that lasts on a plastic fuel tank.

What do I have to do before applying it?

Drain and vent the tank, and make sure there is no fuel, vapor or pressure at the repair area. Sand several inches around the damage down to bare metal, then clean with a solvent such as brake cleaner and let it dry fully. The epoxy will not bond over paint, rust, fuel film or a damp surface, and surface prep is where most failed repairs start.

Is this a permanent repair on a fuel tank?

J-B Weld rates it for permanent or temporary repairs within those size limits, and the cured epoxy is fuel and oil resistant. Be realistic about your own job: a small seam weep on a clean, flat, rigid surface can hold indefinitely, while a larger hole in a tank that flexes or takes road impact should be treated as temporary until the tank is replaced or professionally repaired.

Can I sand and paint the finished repair?

Not well. The resin in this kit cures with fiberglass cloth in it, so it does not sand smooth and it does not take paint well. If you need a repair you can sand, drill, tap and paint, use SteelStik (8267), J-B Weld Original (8265) or TankWeld epoxy putty (8217) instead, all of which finish much better.

Other repairs using TankWeld Kit

NEED HELP FINDING THE RIGHT PRODUCT FOR YOUR PROJECT

FIND YOUR FIX